Treoir Úsáideora don Amaire Saotharlainne Inrianaithe 5002CC

Amaire Saotharlainne Inrianaithe 5002CC

Aláraim
Each channel has a distinct electronic tone that sounds at the end of its timing period. Channel One has one repeating beep; Channel Two has two repeating beeps; and Channel Three has three repeating beeps. A channel’s tone will sound for 1 minute then shut off automatically to preserve battery life.

AN TAISPEÁINT A GHLACADH GO ZERO

Press and hold (approximately 2 seconds) the 1, 2, or 3 button to clear the display to zero for Channel One, Two, or Three respectively. If no channel is active, pressing and holding the 1, 2, or 3 button will shut off the unit entirely.

OIBRÍOCHT AMA

All three timing channels work essentially the same way, so once you understand how Channel One operates, Channels Two and Three will seem extra easy.

AG SOCRÚ AM COMHAIREAMH SÍOS

1. Press the 1 button, digital display will then show all zeros. The symbol will be below the 1 button indicating Channel One is displayed.
2. Set the hours to be timed: Press the H button until the desired number of hours are displayed. For rapid advancement, press and hold button.
3. Set the minutes to be timed: Press the M button until the desired number of minutes are displayed. For rapid advancement, press and hold button.
4. Set the seconds to be timed: Press the S button until the desired number of seconds are displayed. For rapid advancement, press and hold button.
5. When the desired amount of time is showing on the digital display, simply press the 1 button to begin timing. You’ll know timing has begun when the seconds start counting down.
6. A single repeating electronic tone will sound at the end of the timing period and the symbol below the 1 button indicates status of the timing operation. (See “Channel Indicators” table).
7. To reset a channel to zero, to turn off a channel, or to turn off a channel while it is timing, simply press and hold down the appropriate channel (Channel One, Two or Three) for two seconds.

NÓTA: The tone will continue to sound for 1 minute or until it is turned off. To turn off the tone, simply press the 1 button and release.

EXAMPLES
Channels Two and Three operate the same way as Channel One, except you press the 2 button for Channel Two or the 3 button for Channel Three in every instance you pressed the 1 button when timing in Channel One. Two exampTugtar les.

Example 1
Time 1 hour, 20 minutes, and 30 seconds in Channel 2:

1. Brúigh 2 cnaipe.
2. Press H button once to read “1”.
3. Press M button until display reads “20” minutes.
4. Press S button until display reads “30” seconds.
5. Press 2 button to start timing.
6. When the tone (two repeating beeps) sounds, press 2 button to turn it off.

Example 2
Time 9 hours, 15 minutes, and 10 seconds in Channel 3:

1. Brúigh 3 cnaipe.
2. Press H button until display reads “9” hours.
3. Press M button until display reads “15” minutes.
4. Press S button until display reads “10” seconds.
5. Press 3 button to start timing.
6. When the tone (three repeating beeps) sounds, press 3 button to turn it off.

SONRAÍOCHTAÍ

• Taispeáin: ¼* high, 5-digit  LCD
• Timing capacity: 9 hrs, 59 mins, 59 sec
• Taifeach: 1 sec Accuracy: 0.001%
• Size, weight: 3 x 3 x 1⅜”, 4 oz

TAGAIRT THAPA

• Taispeántar Cainéal A
• B- Cnaipe Cainéal a hAon (1)
• C- Cnaipe Cainéal a Dó (2)
• Cnaipe D- Cainéal a Trí (3)
• Níl an t-amchlár ag baint leis an gcainéal leictreonach ná níl sé á thaispeáint.
• Tá an t-am ag baint úsáide as cainéal F ach ní thaispeántar é.
• G - Cnaipe Uaireanta (H)
• H- Minutes (M) button
• I – Seconds (S) button

Táscairí Cainéal
LCD indicators report the status of each channel.

ATHCHÓIRIÚ Battery

To replace the batteries, remove the back housing of the timer by giving the large screw on the back of the unit a half turn with a coin or screwdriver, then replace batteries as shown using two “AA” alkaline batteries. (Do not use regular or heavy-duty batteries. They do not have sufficient power to drive the unit.)

Tar éis cadhnraí a chur isteach, cinntigh go bhfuil taispeántas an lasc ama ag feidhmiú i gceart. Le linn oibríochta an ama, d’fhéadfadh codanna gealánacha a bheith le feiceáil ar an taispeántas. Má tharlaíonn sé seo, is féidir é a athshocrú trí na cadhnraí a bhaint agus a chur isteach arís. Ba chóir go mairfeadh gach sraith cadhnraí 1 go 2 bhliain faoi ghnáthchoinníollacha. Fanfaidh an taispeántas LCD bán nuair is gá cadhnraí a athsholáthar.

BARÁNTA

BARÁNTA, SEIRBHÍS, NÓ ATHCHLÁRÚ
Le haghaidh bharántas, seirbhíse, nó athchalabrú, déan teagmháil le:

TÁIRGÍ IN-INFHEISTÍOCHTA 12554 Sean Bóthar Galveston. Suite B230 Webster, Texas, 77598 USA

• tUltach 281 482-1714
• Facs 281 482-9448
• R-phost tacaíocht@traceable.com
• www.traceable.com

Traceable® Products are ISO 9001:2015 Quality- Certified by DNV and ISO/EC 17025:2017 accredited as a Calibration Laboratory by A2LA.

Cat. Uimh. 5002
Is trádmharc cláraithe de Cole-Parmer é Traceable®.

©2020 Táirgí Traceable®. 92-5002-00 Ath. 6 070825

CCanna