Treoir Oibriúcháin M5StickC Plus2
Firmware mhonarcha
Nuair a bhíonn fadhbanna oibríochta ag an bhfeiste, is féidir leat iarracht a dhéanamh an fhirmchlár monarchan a ath-splancadh chun a sheiceáil an bhfuil aon mhífheidhmiú crua-earraí ann. Féach ar an rang teagaisc seo a leanas. Bain úsáid as uirlis splancadh firmchlár M5Burner chun an fhirmchlár monarchan a splancadh ar an bhfeiste.
CCanna
C1: Cén fáth go bhfuil scáileán dubh ar mo M5StickC Plus2/nach dtosaíonn sé?
Réitigh: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
C2: Cén fáth nach n-oibríonn sé ach 3 uair an chloig? Cén fáth a ngearrtar é 100% i nóiméad amháin, má bhaintear an cábla muirir múchfar é?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Please burn back official firmware.
Ullmhúchán
- Refer to the M5Burner tutorial to complete the firmware flashing tool download, and then refer to the image below to download the corresponding firmware.
Nasc íoslódáil: https://docs.m5stack.com/en/uiflow/m5burner/intro
Suiteáil tiománaí USB
Driver Installation Tip
Click the link below to download the driver matching your operating system. The driver package for the CP34X (for the CH9102 version) can be downloaded and installed by selecting the installation package corresponding to your operating system. If you encounter issues with program download (such as timeout or “Failed to write to target RAM” errors), try reinstalling the device driver.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS v1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Port Selection on MacOS
On MacOS, there may be two available ports. When using them, please select the port named wchmodem.
Roghnú Calafoirt
Ceangail an gléas leis an ríomhaire trí chábla USB. Tar éis suiteáil an tiománaí a bheith críochnaithe, is féidir leat an port gléis comhfhreagrach a roghnú in M5Burner.
Dóigh
Cliceáil “Dóigh” chun an próiseas splancála a thosú.
BataC-Plus2
SKU:K016-P2
Cur síos
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Teagaisc
UIFlow
Tabharfaidh an rang teagaisc seo léargas ar conas an gléas StickC-Plus2 a rialú tríd an ardán ríomhchlárúcháin grafach UIFlow.
UiFlow2
Tabharfaidh an rang teagaisc seo isteach conas an gléas StickC-Plus2 a rialú tríd an ardán ríomhchlárúcháin grafach UiFlow2.
IDE Arduino
Tabharfaidh an rang teagaisc seo léargas ar conas an gléas StickC-Plus2 a chlárú agus a rialú ag baint úsáide as an Arduino IDE.
Nóta
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Gnéithe
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Micreafón comhtháite
- User buttons, 1.14-inch LCD, power/reset button
- Ceallraí Li-ian 200 mAh
- Ceanglóir leathnaithe
- Integrated passive buzzer
- Wearable & mountable
- Ardán Forbartha
- UiFlow1
- UiFlow2
- IDE Arduino
- ESP-IDF
- ArdánIO
Áirítear
- 1 x Bata C-Plus2
Feidhmchláir
- Gléasanna inchaite
- IoT controller
- STEM education
- Tionscadail DIY
- Gléasanna cliste tí
Sonraíochtaí
| Sonraíocht | Paraiméadar |
| SoC | ESP32-PICO-V3-02 240 MHz dé-chroí, Wi-Fi, 2 MB PSRAM, 8 MB Splancchuimhneacháin |
| Ionchur Voltage | 5 V @ 500 mA |
| Comhéadan | Cineál-C x 1, GROVE (I2C + I/O + UART) x 1 |
| Scáileán LCD | 1.14 orlach, 135 x 240 Dath TFT LCD, ST7789V2 |
| Micreafón | SPM1423 |
| Cnaipí | Cnaipí úsáideora x 3 |
| stiúir | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| dordánaí | Buzzer éighníomhach ar bord |
| IMU | MPU 6886 |
| Antenna | Antenna 2.4 G 3D |
| Pionnaí Seachtracha | G0, G25/G26, G36, G32, G33 |
| Ceallraí | 200 mAh @ 3.7 V, istigh |
| Teocht Oibriúcháin | 0 ~ 40 °C |
| Imfhálú | Plaisteach (PC) |
| Méid an Táirge | 48.0 x 24.0 x 13.5mm |
| Meáchan Táirge | 16.7 g |
| Méid Pacáiste | 104.4 x 65.0 x 18.0mm |
| Meáchan Comhlán | 26.3 g |
Treoracha Oibriúcháin
Cumhacht ar / As
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Scéimre
Léarscáil bioráin
LED Dearg & Astaire IR | Cnaipe A | Cnaipe B | Buzzer
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Cnaipe A | Cnaipe A | ||||
| Cnaipe B | Cnaipe B | ||||
| Cnaipe C | Cnaipe C | ||||
| Buzzer éighníomhach | dordánaí |
Dath TFT Taispeáin
Driver IC: ST7789V2
Taifeach: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| Taispeántas TFT | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Micreafón MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | SONRAÍ |
IMU 6-Ais (MPU6886) & RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| Emitter IR | TX | ||
| LED dearg | TX |
HY2.0-4P
| HY2.0-4P | Dubh | Dearg | Buí | Bán |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Méid an tSamhail
Bileoga sonraí
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU 6886
SPM1423
Bogearraí
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
Tús Tapa UiFlow1 StickC-Plus2
UiFlow2
Tús Tapa UiFlow2 StickC-Plus2
ArdánIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
creat = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
Tiománaí USB
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Ainm tiománaí | Supported Chip | Íosluchtaigh |
| CH9102_VCP_SER_Windows | CH9102 | Íosluchtaigh |
| CH9102_VCP_SER_MacOS v1.7 | CH9102 | Íosluchtaigh |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Íosluchtaigh | Nóta |
| Factory Test for Windows | íoslódáil | / |
Eile
Treoir Firmware Monarcha Athchóirithe StickC-Plus2
Físeán
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Athrú Leagan
| Dáta Eisiúna | Athrú Cur síos | Nóta |
| / | An chéad eisiúint | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Comparáid Táirge
Difríochtaí Crua-earraí
| Táirge Ainm |
SoC | Bainistíocht Cumhachta | Cumas Battery | Cuimhne | Sliseanna USB-UART | Dath |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- orange |
| BataC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | Oráiste |
Difríochtaí bioráin
| Ainm Táirge | IR | stiúir | TFT | BUTTON A. | Cnaipe B | CNAIPÉ C (DÚIS) |
LEANBH | Ceallraí Imltage Braith |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | rialta cnaipe |
/ | Trí AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Difríochtaí Cumhachta Ar Siúl/Múchta
| Táirge Ainm | Cumhacht Ar | Cumhacht Off |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Ós rud é go mbaintear an PMIC AXP192 as an StickC-Plus2, tá an modh cumhachtaithe ar siúl/as difriúil ó leaganacha roimhe seo. Mar a luadh ag tús an doiciméid seo, tá an oibríocht cosúil go mór, ach beidh na leabharlanna tacaithe difriúil. Tá feabhas curtha ar neart comhartha Wi-Fi agus IR i gcomparáid leis an tsamhail roimhe seo.
Doiciméid / Acmhainní
 |
Modúl Forbartha Idirlín na Rudaí M5STACK ESP32-PICO-V3-02 [pdfTreoir Úsáideora Modúl Forbartha Idirlín na Rudaí ESP32-PICO-V3-02, ESP32-PICO-V3-02, Modúl Forbartha Idirlín na Rudaí, Modúl Forbartha, Modúl |