Jaycar Digitech QC1938 100MHz Digital Oscilloscope User Manual

1. Réamhrá

This manual provides detailed instructions for the safe and effective operation of your Jaycar Digitech QC1938 100MHz Digital Oscilloscope. Please read this manual thoroughly before using the device to ensure proper setup, operation, and maintenance. Retain this manual for future reference.

2. Faisnéis Sábháilteachta

Observe the following safety precautions to prevent injury and avoid damage to the instrument or any products connected to it.

• Foinse Cumhachta: Connect the oscilloscope only to the power source specified in this manual.
• Bunús: Cinntigh go bhfuil an ionstraim talmhaithe i gceart chun turraing leictreach a chosc.
• Tóraithe: Use only probes supplied or recommended by the manufacturer. Ensure probes are rated for the voltage á thomhas.
• Aeráil: Ná bac na hoscailtí aerála. Cinntigh go bhfuil sreabhadh aeir leordhóthanach timpeall an uirlis.
• Timpeallacht: Operate the oscilloscope in a dry environment. Avoid exposure to moisture, dust, or extreme temperatures.
• Ag seirbhísiú: Tabhair aird phearsanra seirbhíse cáilithe ar gach seirbhísiú. Ná déan iarracht an uirlis a dheisiú leat féin.

3. Ábhar Pacáiste

Deimhnigh go bhfuil na míreanna go léir atá liostaithe thíos i láthair i do phacáiste:

• Jaycar Digitech QC1938 Digital Oscilloscope
• 10:1 Passive Probe with 1.5m lead
• 2 x BNC to Clip Test Leads
• Cábla USB
• Cumhacht Luaidhe
• Lámhleabhar Úsáideora (an doiciméad seo)

4. Táirge Tharview

The Jaycar Digitech QC1938 is a 100MHz Digital Oscilloscope designed for precise electronic measurements. It features a 7-inch color LCD screen, two independent channels, and a built-in waveform generator.

Príomhghnéithe:

• 7-inch TFT color LCD screen with 800 x 480 pixel resolution
• Two independent input channels
• 100MHz bandwidth and 1GSa/s sampráta ling
• 8M memory depth (single channel)
• Integrated 25MHz waveform generator (Sine, Square, Ramp, Exponential, Noise, DC)
• Auto scale function for automatic sine and square wave detection
• 14 trigger modes including Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, and IIC
• 5 serial protocol triggers and decodes: RS232/UART, I2C, SPI, CAN, and LIN
• Two 3-digit digital voltmeters and a 6-digit hardware frequency indicator
• 32 types of auto measurements with real-time statistics
• USB Host/Device interface for computer control and data storage

5. Socrú

5.1 Ceangal Cumhachta

1. Connect the supplied power lead to the power input on the rear panel of the oscilloscope.
2. Plug the other end of the power lead into a grounded AC power outlet.
3. Press the power button on the front panel to turn on the oscilloscope.

5.2 Ceangal Próifíle

1. Connect the BNC connector of the passive probe to either Channel 1 (CH1) or Channel 2 (CH2) input on the front panel.
2. Attach the ground clip of the probe to the circuit's ground point.
3. Connect the probe tip to the test point in your circuit.
4. Ensure the probe's attenuation setting (e.g., 1X or 10X) matches the setting on the oscilloscope for accurate readings.

6. Treoracha Oibriúcháin

6.1 Oibríocht Bhunúsach

• Auto Scale: Press the 'AUTO SET' button to automatically adjust vertical, horizontal, and trigger settings for a stable waveform display. This function detects sine and square waves automatically.
• Vertical Controls (VOLTS/DIV, POSITION): Use the VOLTS/DIV knobs to adjust the vertical scale (voltage per division) for each channel. The POSITION knobs shift the waveform vertically.
• Horizontal Controls (SEC/DIV, POSITION): Use the SEC/DIV knob to adjust the horizontal scale (time per division). The horizontal POSITION knob shifts the waveform horizontally.
• Leibhéal Truicear: Adjust the 'TRIGGER LEVEL' knob to set the voltage level at which the oscilloscope captures a waveform.

6.2 Ardfheidhm

• Gineadóir Cruth Tonn: Access the waveform generator menu to select and configure output waveforms such as Sine, Square, Ramp, Exponential, Noise, and DC. Connect the 'WAVE GEN' output to your circuit.
• Modhanna Truicear: Utilize the 14 available trigger modes (Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC) to capture specific events. Select modes via the 'TRIGGER' menu.
• Serial Protocol Decoding: The oscilloscope supports decoding for RS232/UART, I2C, SPI, CAN, and LIN protocols. Configure these settings in the 'DECODE' menu to view decoded data.
• Tomhais: The device offers 32 types of automatic measurements with real-time statistics (maximum, minimum, standard deviation, etc.). Access these via the 'MEASURE' menu.
• Nascacht USB: Connect a USB thumb drive to the USB Host port to save oscilloscope setups, waveforms, reference waveforms, CSV files, and images. The USB Device port allows for remote control from a computer using SCPI commands.

7. Cothabháil

7.1 Glanadh

To clean the instrument, use a soft cloth dampened with a mild detergent solution. Do not use abrasive cleaners or solvents that could damage the casing or screen. Ensure the device is powered off and unplugged before cleaning.

7.2 Stóráil

When not in use, store the oscilloscope in a dry, dust-free environment away from direct sunlight and extreme temperatures. Use the original packaging or a suitable case for protection during transport.

8. Fabhtcheartú

If you encounter issues with your oscilloscope, refer to the following common problems and solutions:

Má leanann an fhadhb ar aghaidh tar éis duit na réitigh seo a thriail, déan teagmháil le tacaíocht do chustaiméirí.

9. Sonraíochtaí

10. Barántas agus Tacaíocht

For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for warranty claims.