GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Réamhrá

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Eolas Sábháilteachta

RABHADH: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Ensure power is OFF at the circuit breaker before installation.
• Tá an gléas seo beartaithe le suiteáil de réir an Chóid Leictreach Náisiúnta agus rialacháin áitiúla.
• Do not use in wet locations or where directly exposed to water.
• Le húsáid laistigh amháin.

Ábhar an Phacáiste

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Scriúnna Suiteáil
• Cnónna Sreinge (d’fhéadfadh sé a bheith éagsúil de réir an phacáiste)
• Lámhleabhar Úsáideora (an doiciméad seo)

Socrú agus Suiteáil

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Múch an chumhacht: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Bain an Sean-Lasc: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Aithin sreanga:
   • Líne (Te): De ghnáth dubh, ag teacht ón mbriseoir ciorcaid.
   • Luchtaigh: De ghnáth dubh, ag dul chuig an daingneán solais nó an fearas.
   • Neodrach: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Ground: Usually green or bare copper.
4. Ceangail Lasc Nua: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Ceangail an Líne wire to the terminal marked "LINE".
   • Ceangail an Luchtaigh wire to the terminal marked "LOAD".
   • Ceangail an Neodrach wire to the terminal marked "NEUTRAL".
   • Ceangail an Talamh wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Lasc Gléasta: Brúigh an lasc sreangaithe isteach sa bhosca balla go cúramach. Daingnigh é leis na scriúnna atá ar fáil.
6. Suiteáil Wall Plate: Ceangail an pláta balla nua nó atá ann cheana féin.
7. Athchóirigh Cumhacht: Cas an chumhacht ar ais AR ag an mbriseoir ciorcaid.

Fíor 1: Tosaigh view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle uair amháin. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Oibriú an Lasc

Rialú Lámhleabhar

• Brúigh an barr of the paddle to turn the connected load ON.
• Brúigh an bun of the paddle to turn the connected load AS.

Rialú Z-Tonn

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Cothabháil

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Glanadh: Chun an lasc a ghlanadh, cuimil é le clúdach bog,amp éadach. Ná húsáid glantóirí nó tuaslagóirí scríobach.
• Nuashonruithe Firmware: Seiceáil an GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Cúram Ginearálta: Ensure the switch is not exposed to excessive moisture or extreme temperatures.

Fabhtcheartú

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle uair amháin. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Sonraíochtaí

Barántas agus Tacaíocht

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webláithreán gréasáin nó déan teagmháil lena rannóg seirbhíse do chustaiméirí.

Websuíomh: www.gocontrol.com

Monaróir: GOCONTROL